No produts were found.

Click for more products.

No produts were found.

0.00 €

Home
/
Products
/
Controllers
/
Easy controllers
/
Easy Controller 1-3 Stack Match

Easy Controller 1-3 Stack Match

This is Easy Controller for antenna stack match with 3 (2) outputs. You can control any stack match with 4 wires. There are 7 combinations. Including PTT hot switch protection. You can choose between two versions: classic and remote. Remote version allows you to control stack match over the web page and there are also another 8 universal On/Off outputs for your use.

Main functions

Universal controller for stack match 1-3
All combinations for 3 antennas
Universal for any stack match with 4 control wires
All outputs are universal +12V or GND
HOT switch PTT protection
IP module with 8 external relays for custom use
DC plug included
IP/web remote module as option version REMOTE
ASSEMBLED and TESTED VERSION

Parameters

Output is universal +12V or + EXT or to GND
Output current max. 500 mA per output, 500 mA total
Output voltage the same as supply voltage or EXT max 26V DC
EXTernal voltage for relays with different voltage than 12V
TBD driver is included
Voltage drop for TBD driver typ. 0.2V for +12V input and 0.7V including fuse
Voltage drop for ULN driver typ. 0.8V for +12V input
PTT hot switch protection active to GND (5V logic compatible)

⚠ IMPORTANT NOTE: Default output setting is with TBD driver. Output control is +12V. If you need to control external devices by switching to ground, you must replace the driver with ULN and change the Jumper settings. ULN driver is NOT included. You can buy it here.

REMOTE VERSION

Remote Module

Control your antenna switch and external 8 outputs with your browser/http
Web based application with automated updates
No configuration or firmware upload needed
Custom button labels by parameter
Customize your UI or use our control view
Can be controlled by stream deck and touchportal
System is part of our station automation infrastructure by DM5XX's RemoteSwitch.de system
Remote Control disables front panel switch
Additional external 8 OUTPUTS - ON/OFF for switching other devices or antennas
External switching: Universal output driver output +12V or GND
LAN connection with unique RFI filtering + HV protection
We recommend a VPN while using remote access from outside your network in general

Parameters for Remote Module/Daughter OLI IP

LAN 10/100 Mbit auto
ONLY DHCP IP address - not static
LAN High Voltage double protection
LAN Common-mode filter = lower RFI emission from LAN cable
Output is universal +12V or + EXT or to GND
Output current max. 500 mA per output, 500 mA total
Output voltage the same as supply voltage or EXT max. 26V DC
EXTernal voltage for relays with different voltage than 12V
TBD driver is included
Voltage drop for TBD driver typ. 0.2 V for +12V input and 0.7 V including fuse
Voltage drop fro ULN driver typ. 0.8 V for +12V input
EXTERNAL 8 outputs for custom use

Available as

ASSEMBLED: classic version - ready to use
ASSEMBLED: remote version - ready to use

RECOMMENDATIONS TO BUY:

Included in package

Controller assembled and tested
DC plug - image
DB15 male connector with cover
DB9 female connector with cover (remote version)

Technical articles

Please check our technical articles about REMOTE SYSTEM.

Manual

If you want to know more please check our wiki with Easy Controller manual.

Easy controller remote version

User Interfaces

User interfaces (UI) can be divided into three groups:
- Classic UI - looks like the RF controller front panel
- Beam Map - Azimuthal map with control buttons
- Customs, Stream Deck, NodeRed etc.

Example for remote control User Interface (UI), there for 1-3 Stack Match Easy controller

example for External Relays

- You can use another 8 external relays. You can control another 8 things you like. It is simply 8 x ON/OFF
- Outputs can be configured as: switching to ground + voltage
- Output voltage could be the same as controller supply voltage or different - connected to Vext pin at connector

example with 8 Relay DIN module

block diagram for LAN core

This Easy Controller is for our 1-3 Stack Match

HV8DC board

This is a specially designed board to protect up to 8 DC control wires. The connection between the control box and the equipment outside (on the mast) can be dangerous - due to storms a potential difference can easily occur or voltage can be induced on the control wires. This phenomenon is dangerous and it is necessary to safely discharge this voltage to a common earth potential.

The controller contains basic surge protection. However, it is not very safe to bring surges to the table in Hamshack! If the GND screw of the control box is not connected to a common ground, the surge can go through another device - DC power supply, LAN, etc. It is therefore better to place an additional surge protector between the control box and the equipment outside. For example, at the point where cables enter the building from the outside, it is a good idea to place this surge protector board to provide additional protection against surge entering the ham shack.