56.87 €
(tax incl.)
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
Single wire beverage CLASSIC KIT
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
56.87 €
(tax incl.)
56.87 €
47.00 € (without tax)
47.00 € (without tax)
Brand:
Add to compare0
Love
Add to wishlist
This Single wire beverage classic is a long wire antenna installed very close to the ground. The antenna should be longer than 1 wavelength and installed at a height of less than 0.05 wavelength above ground. The beverage is usually terminated in a resistance at the end (opposite the feedpoint). Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
Using
- Low band receiving antenna
- Lower noise, better directivity
- Can be part of phased array
Main functions
- Broadband 0.1 to 30 MHz
- Single directional
- Low noise
- Protections - high voltage/current
- Termination resistance selectable in three steps
- 50/75 Ohm feed line - easy jumper switch
- Common-mode coax choke included
- Electrostatic protection with neon lamps
- High power protection
- Stainless screws
- High quality connectors
- IP56 boxes - recommended to protect it against water
- Feeder size 100x100 mm
- Terminator size 64x58 mm
- KIT VERSION
Parameters
- Coax impedance 50 or 75 Ohm (internal jumper)
- Construction as you need
Available as
KIT: all parts + PCBs and IP56 boxes
ASSEMBLED: ready to use - ASSEMBLED VERSION
Connectors: PL SO-239 or F
PCB: only PCBs
KIT contains
- PCBs - feeder and terminator
- box IP56 (100x100 mm and 64x58 mm)
- connector (PL SO-239 OR F)
- neon lamps
- resistors
- PTC resettable fuses
- ferrite cores
- binocular core
- pin headers, jumpers
- fasteners (screws, nuts, washers, ring terminals, spacer bolt)
- coax cable
- Cu wire
- wires
- holder for common-mode coax choke
- stickers
- paper drilling template
- PCB for F connector
Manual
If you want to know more please check our wiki with Single wire beverage classic manual.
version with PL SO-239 connector
version with F connector
assembled version with PL SO-239 connector
assembled version with F connector
assembled version of terminator
block diagram
example of right configuration with CMCC
typical SWR
Data sheet
- type
- KIT
- design
- in enclosure
- usage
- RX
- impedance
- both 50 & 75 Ohm
- front-end protection
- output
- frequency range
- 0.1 MHz to 30 MHz
- product dimensions
- 65x58x35 mm - PU box IP56
100x100x50 mm - PU box IP56
- PCB dimensions
- 50x25 mm
50x33 mm
- product weight (brutto)
- 0.42 (F), 0.45 (PL) kg
- package dimensions
- 18.5x14x10.5 cm
Specific References
- ean13
- 1000090104717
You may also like
83.49 €
(tax incl.)
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
235.95 €
(tax incl.)
This is 2 element beverage antenna array. In this End-Fire array the beverage antennas are very close to each other. Usually 2 to 6 meters. One beverage is shifted to front by the stagger distance. This array needs...
16.94 €
(tax incl.)
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
16.94 €
(tax incl.)
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
13.31 €
(tax incl.)
This is set of insulators for Single Wire beverages. Set includes 10 pieces.
15.73 €
(tax incl.)
This is set of insulators for Single Wire beverages. Set includes 22 pieces.
16.94 €
(tax incl.)
This is set of insulators for Single Wire beverages. Set includes 24 pieces.
83.49 €
(tax incl.)
Beverage antennas provide one of the least expensive and most reliable ways to improve DX capabilities on the low frequencies.
Leave a review