271.04 €
(tax incl.)
High Power 6-to-1 antenna switch - six outputs to one input.
BCD to DEC converter
Simply but powerful converter/decoder from BCD data to one of eight. You can use it everywhere you have less wires than you need.
62.92 €
(tax incl.)
62.92 €
52.00 € (without tax)
52.00 € (without tax)
Brand:
Add to compare0
Love
Add to wishlist
This converter/decoder BCD to DEC is a simply but very powerful device. It decode from BCD data to one of eight. You can use it everywhere you have less wires than you need. You need only 4 wires and control up to 8 outputs. You can supply external relays over the BCD data wires. There is universal output driver. You can drive outputs by switching to GND or + Vcc voltage. BCD inputs include RF and high voltage protection.
Using
- Universal converter/decoder BCD to DEC
- Compatible with Ameritron switches
- When you miss wires to your tower :)
- Remote control expander
Main functions
- BCD to DEC matrix table
- Outputs 0 to 7 or 1 to 8 (jumper)
- Universal OUTPUT: + or GND
- No external voltage needed. Up to 0.5 A by the BCD wires
- BCD input 9 to 13.8 V
- TBD and ULN drivers are included
- RF and high voltage protections
- ASSEMBLED and TESTED VERSION
Parameters
- Output current max. 500 mA
- Voltage drop for TBD driver typ. 0.2V for +12V input and 0.6V for BCD wires power input
- Voltage drop for ULN driver typ. 0.8V for +12V input and 1.3V for BCD wires power input
- Input voltage > 13V is recommended for 12V relays
- Control voltage for BCD input is 9 to 14V
- Low loss in switching driver
- Universal output switching: to GND or + Vcc
- Output 0 for 0000 BCD or 8 for 0001 - easy select by jumper
- Compatible with Ameritron MCS-10
- PCB size 90x52 mm
Available as
ASSEMBLED: ready to use
RECOMMENDATIONS TO BUY:Included in package
BCD assembled and tested
ULN and TBD drivers - image
Manual
If you want to know more please check our wiki with BCD to DEC converter manual.
Matrix table for inputs and outputs
 |
Connection example 1
- without external power voltage wire
- less wires
- for fat wires or smaller distance
Connection example 2
- with external power voltage wire
- one more wire
- BCD wires can use smaller voltage > 9 V
- for longer distance
Output 0 to 8
- compatible with MFJ antenna switch
- easy to set by jumper
Output driver
- universal outputs - switching to GND or + voltage
- easy to se by jumper
- easy to replace driver ULN (- out) / TBD (+ out)
Example with 6-to-1
- need four (five) wires between controller and BCD to DEC converter
- GND, (+12V) and three control wires
- output must be with TBD driver (+ out)
Example with 4-to-1
- need three (four) wires between controller and BCD to DEC converter
- GND, (+12V) and three control wires
- output must be with TBD driver (+ out)
This is a specially designed board to protect up to 8 DC control wires. The connection between the control box and the equipment outside (on the mast) can be dangerous - due to storms a potential difference can easily occur or voltage can be induced on the control wires. This phenomenon is dangerous and it is necessary to safely discharge this voltage to a common earth potential.
Data sheet
- type
- ASSEMBLED
- design
- pcb module
- usage
- RX + TX
- front-end protection
- input and output
- PCB dimensions
- 90x52 mm
- product weight (brutto)
- 0.07 kg
- package dimensions
- 12x10.5x4.5 cm
You may also like
482.79 €
(tax incl.)
This is high isolation, low loss 6 to 2 RF switch.
68.97 €
(tax incl.)
Simply but powerful converter/decoder from BCD data in TTl logic to one of eight. You can use it everywhere you have less wires than you need.
68.97 €
(tax incl.)
Simply but powerful converter/decoder from BCD data input to 16 outputs, compatible with Yaesu BCD. You can use it everywhere you have less wires than you need and also with BCD (TTL) output devices (like Microham).
258.94 €
(tax incl.)
High Power 4-to-1 antenna switch - four outputs to one input.
83.49 €
(tax incl.)
High Power 6-to-1 antenna switch - six outputs to one input.
