98.01 €
(tax incl.)
This one coax output beverage antenna has got internal relay for direction switching.
4-way switch for Bi-directional beverages KIT
This is two port antenna switch - middle box between pair of Bi-Directional antennas with single coax output.
60.50 €
(tax incl.)
60.50 €
50.00 € (without tax)
50.00 € (without tax)
Brand:
Add to compare0
Love
Add to wishlist
This 4-way RX antenna switch is in the middle box between the pair of Bi-Directional antennas with single coax output. It allows you to control ALL 4 directions over one coax cable. Directions are controlled by voltage over the coax (0, +12V, -12V and AC).
Using
- Four direction beverage system classic version and remote version
- Four direction RX antenna with two Bi-Dir antennas - example
Main functions
- 4-way switch for RX antenna
- Broadband - 0.1 to 50 MHz
- 50 or 75 Ohm feed line version
- Common-mode coax choke included for OUTPUT port
- Electrostatic protection with neon lamps
- High voltage protections
- High quality connectors
- Stainless screws
- IP56 box - recommended to protect it against water
- Size 100x100 mm
- KIT VERSION
Parameters
- Control voltage up to 15 V AC/DC
- Maximal current up to 300 mA
- Insertion loss less than 0.5 dB
- Common-mode current choke with isolation over 30 dB at output port
- Controlled by - 12 V DC or AC
Available as
KIT: all parts + PCB and IP56 box
ASSEMBLED: ready to use - ASSEMBLED VERSION
Connectors: PL SO-239 or F
PCB: only PCB
KIT contains
- PCB
- box IP56 (100x100 mm)
- connectors (PL SO-239 OR F)
- neon lamps
- resistors
- capacitors
- inductors
- varistors
- diodes
- LED diode
- relays
- ferrite cores
- fasteners (screws, nuts, washers, spaces bolts, ring terminals, cable tie)
- coax cable
- wire
- sticker
- paper drilling template
- PCBs for F connector
Manual
If you want to know more please check our wiki with 4-way switch for Bi-directional beverages manual.
⚠ IMPORTANT NOTE: This switch is controlled by NEGATIVE VOLTAGE - 12 V or AC
version with PL SO-239 connectors
version with F connectors
assembled version with PL SO-239 connectors
assembled version with F connectors
example with Bias tee and Bi-dir antennas
Data sheet
- type
- KIT
- design
- in enclosure
- usage
- RX
- impedance
- both 50 & 75 Ohm
- front-end protection
- none
- frequency range
- 0.1 MHz to 50 MHz
- product dimensions
- 100x100x50 mm - PU box IP56
- product weight (brutto)
- 0.35 (F), 0.42 (PL) kg
- package dimensions
- 18.5x14x10.5 cm
Specific References
- ean13
- 1000090096388
You may also like
88.33 €
(tax incl.)
This is two port antenna switch - middle box between pair of Bi-Directional antennas with single coax output.
98.01 €
(tax incl.)
This one coax output beverage antenna has got internal relay for direction switching.
16.94 €
(tax incl.)
This is PCB for two port antenna switch - middle box between pair of Bi-Directional antennas with single coax output.
16.94 €
(tax incl.)
A bias tee is used to insert AC or DC power into an HF signal to power remote antenna preamplifiers (DC), Bi-directional beverages (AC) or other devices.
64.13 €
(tax incl.)
This one coax output beverage antenna has got internal relay for direction switching.
16.94 €
(tax incl.)
PCBs for one coax output beverage antenna.
76.23 €
(tax incl.)
A bias tee is used to insert AC or DC power into an HF signal to power remote antenna preamplifiers (DC), Bi-directional beverages (AC) or other devices.
43.56 €
(tax incl.)
A bias tee is used to insert AC or DC power into an HF signal to power remote antenna preamplifiers (DC), Bi-directional beverages (AC) or other devices.
309.76 €
(tax incl.)
This is antenna controller for K9AY and Bi-directional beverages. You can use DC control wires as well as AC/DC voltage over the coax to antenna. There are Band Pass Filters and preamplifier directly in the...