2-way active splitter in BOX
This is very useful device - this is active splitter version in enclosure. It can provide equal voltages, equal current, or equal power to matched or unmatched loads. Input low noise amplifier can eliminate insertion loss of the splitter and add small gain.
82.00 € (without tax)
This 2-way active splitter in BOX is a very useful device. It can provide equal voltages, equal current, or equal power to matched or unmatched loads. This is active splitter version where you can switch ON high IP, low noise preamplifier and eliminate insertion loss of the splitter. Gain can be set as you need by the Variable ATT at PCB. This HW is designed only for RX line. There are some more high current and voltage protections on all ports. Both impedances 50 or 75 Ohm can be selected by je jumper.
Using
- Antenna splitter
- RX signal divider
Main functions
- Broadband: 0.1 MHz to 60 MHz
- 2-way splitter
- Passive (4.5 dB loss) or Active (up to 14 dB gain)
- Bypass of Preamp by relays
- Low loss, high gain, low noise, high IP3 preamplifier
- Front-end protections - high voltage / current
- 50 / 75 Ohm impedance - easy jumper switch
- Electrostatic protection by neon lamps
- High power protection
- Quality SMA connectors
- Aluminium enclosure: W x H x L = 74 x 29 x 100
- 4pcs self adhesive feet pads included
- DC plug included
- ASSEMBLED and TESTED VERSION
Parameters
- Impedance 50 or 75 Ohm
- NPN transistor 2SC5551A
- Supply voltage 12 - 14 V
- BIAS current 10 to 70 mA
- Supply current up to 180 mA includes relays
- Gain: up to 14 dB
- Low Noise Figure (NF) 1.2 dB (20 mA 50 MHz)
- Low Noise Figure (NF) < 2 dB (60 mA 50 MHz)
- REAL IP3 34 dBm
- Input diode limiter about +17 dBm
- Bypass of Preamp without supply voltage
- Insertion loss with preamp OFF: around 1.5 dB together with the splitter around 4.5 dB
- Insertion loss with preamp ON: from about 20 dB loss (ATT with too high set) to 14 dB GAIN
- Isolation more than 20 dB, 160-40m more than 30 dB
- SWR on OUT (splitted) ports better than 1 : 1.1 on HF, resp. 1 : 1.19 on 6m
- SWR on IN port around 1 : 1.2 to 1 : 1.7 depends on gain of preamp (Optimal is 10 dB)
- Maximal RF current: 100 mA
- Maximal RF voltage: around 65 V
Available as
ASSEMBLED BOX: ready to use
ASSEMBLED MODULE: ready to use - MODULE VERSION
Included in package
Splitter assembled and tested
DC plug - image
4pcs self adhesive feet pads - image
Manual
If you want to know more please check our wiki with 2-way active splitter manual.
Only two way splitter without preamplifier
Example for two RX with preamplifier
Example for RX and SDR with preamplifier
Isolation and SWR at OUT
In to OUT, Preamp OFF
In to OUT, Preamp ~10 dB
In to OUT, Preamp max Gain
Data sheet
- type
- ASSEMBLED
- design
- in enclosure
- usage
- RX
- impedance
- both 50 & 75 Ohm
- front-end protection
- input and output
- frequency range
- 0.1 MHz to 60 MHz
- product dimensions
- 100x74x29 mm - al box
- product weight (brutto)
- 0.27 kg
- package dimensions
- 14.5x9.5x9.5 cm
Specific References
- ean13
- 1000090112903
Leave a review