Remotius 64
This is IP controller designed for direct connection with our K9AY++/4-way and 7ANT controllers.
270.00 € (without tax)
Remotius 64 is IP controller designed for direct connection with our K9AY++/4-way and 7ANT controllers at the first three banks or universal 12, 12, 13 and 16 outputs, one analog input (for 4SQ dummy load power), many temperature sensors for your PA, room, PS etc. Remotius 64 offers web based User Interface, Beam Map control or any other system (NodeRed, Stream Deck etc.). Outputs including DC protection - electronic fuse. LAN port is 100 Mbit with double common-mode filter and high voltage protection. LED indications show status of the remote controller (each bank). There is also PTT hot switch protection when needed.
Main functions
- Universal controller with 53 (total) outputs
- Each bank could have own User Interface
- Multi users control possible
- Web based control with User Interfaces, Stream Deck, NodeRed etc.
- Bank 1: 12 outputs, directly designed for K9AY++/4-way or 7ANT
- Bank 2: 12 outputs, directly designed for 7ANT
- Bank 3: universal 13 OUT (also 7ANT, 6-to-2, beverage switch etc.)
- Bank 4: universal 16 OUT switching to ground
- Bank 1 and 2 with PTT IN, shared Analog IN (4SQ DL PWR)
- Bank 1 to 3 have positive voltage outputs - TBD - image
- Bank 4 has negative voltage outputs - ULN - manual
- PTT hot switch protection built in (when needed)
- One PTT for ALL banks
- Up to 10 temperature sensors (18B20) - image
- Easy to use with your own hardware
- Web based application with automated updates
- No configuration or firmware upload needed
- Custom button labels by parameter
- Customise your UI or use our control view
- Can be controlled by Stream Deck and touchportal
- System is part of our station automation infrastructure by DM5XX's RemoteSwitch.de system
- We recommend a VPN while using remote access from outside your network in general
- Easy configuration with EASY ASSISTANT
- DC plug included
- ASSEMBLED and TESTED VERSION
Parameters
- Universal 53 outputs with + voltage or GND outputs (depends on bank) - image
- Controller supply voltage 12 ~ 14 V, max. 16 V DC/1.5 A - DC plug cable
- BANK 1 to 3 have positive drivers max. 26 V DC
- BANK 4 is switching to Ground
- JUMPERS for different configuration (see manual)
- BANK 1 and 2 need EXT power supply max. 26 V DC
- BANK 3 internal or EXT power supply controller voltage or EXT max. 26 V DC
- BANK 4 could have 12 V output for external devices (relays), max. 0.5 A
- BANK output current max. 500 mA per output, 700 mA total per bank
- Voltage drop for positive driver typ. 0.2 V for + 12 V input and 0.7 V including fuse
- Output voltage for positive driver is input voltage minus about 0.7 V
- BANK 4 voltage droop typ. 0.8 V for + 12 V
- LED indication: ON BANK and PTT
- Temperature sensor: up to 10 of 18B20
- PTT IN: RCA or Bank 1 or 2
- PTT HOT switch protection for ALL banks
- PTT OUT: FET 0.5 A, 50 V DC (no delay)
- Analog input: max. 16 V DC
- LAN 10/100 Bit with filter and protection
- ONLY DHCP IP address - not static
BANKs summary
- BANK 1 and 2: positive output needs external DC supply (max. 26 V, 0.7 A)
- BANK 3: positive output supply from controller or Vext (pin 15), (max. 26 V, 0.7 A)
- BANK 4: negative output switching to ground (max. 50 V, 0.5 A per pin). Possible DC out for ext. device
- BANK 4: possible DC out for ext. device Controller supply voltage, max. 0.5 A
Analog input
- One analog input for 4SQ UI
- Simply indication - low accuracy ADC
- Possible to use BANK 1 or 2 (shared one ADC)
- Internal 30 turn trimmer for scale set
- Full scale Voltage: min. typ. 4.2 V, max. 16 V DC
- Overdrive protection
Temperature sensor
- Optional input designed for 18B20 sensors
- Star topology connection for more sensors
- You can use up to 10 pieces
- Sensor voltage 3V3
- Simply RFI filter
Available as
ASSEMBLED: ready to use
RECOMMENDATIONS TO BUY:- Temperature sensor
- D-SUB 15 cable
- D-SUB 15 female connector pcb version
- D-SUB 15 female connector enclosure version
- D-SUB 25 male connector enclosure version
Included in package
Controller assembled and tested
3pcs DB15 female connector with cover
DB25 male connector with cover
Connector for 18B20 temperature sensor
DC plug - image
Technical articles
Please check our technical articles about REMOTE SYSTEM.
Manual
If you want to know more please check our wiki with Remotius 64 manual.
example with D-SUB connectors
Data sheet
- type
- ASSEMBLED
- design
- in enclosure
- usage
- RX + TX
- impedance
- 50 Ohm
- front-end protection
- input and output
- frequency range
- 0.1 MHz to 60 MHz
- product dimensions
- 200x120x50 mm - al box
- product weight (brutto)
- 0.73 kg
- package dimensions
- 27.5x22.5x9.5 cm
Leave a review