FNIRSI DSO-TC3
Smarty meter 3in1
78.65 €
(tax incl.)
78.65 €
65.00 € (without tax)
65.00 € (without tax)
Brand:
Add to compare0
Love
Add to wishlist
This is a very smart device - smarty meter. It is a combination of a digital oscilloscope, signal generator, universal electronic component tester, V-meter, temperature sensor meter, IR LED decoder and much more in one device with a 2.4 inch display and bulit-in lithium battery.
The device also comes with a set of accessories: component measurement cables, signal generator output cable and oscilloscope probe (X1, X10) with adapter.
In addition, you also get a DURABLE CASE FOR FREE!
The oscilloscope allows basic measurements, the generator has 6 signal shape options with frequency and amplitude settings and the universal tester allows you to identify a large number of electronic components including pin recognition and parameter measurement.
Basic technical data
- display screen: 2.4 inch TFT
- supply voltage: lithium battery
- charging: by USB-C, +5V
- size: 79x103x31 cm
Oscilloscope
- Real-time sampling rate 10MSa/s and bandwidth of 500kHz
- Sample Rate: 10MSa/s
- Analog Bandwidth: 500kHz
- Input impedance: 1MOHm
- Coupling: AC/DC
- Voltage range: 400V
- Vertical sensitivity (X1): 10mV to 10V
- Horizontal time base range: 1is to 10s
- Trigger mode: Auto/Normal/Single
- Trigger type: Rising/Falling edge
- Waveform freeze: Yes
- Automatic measurement: Yes
Signal Generator
- The signal Generator has a total of 6 waveform to choose from and adjustable frequency and amplitude
- Sine wave: 1 to 100kHz, 0 to 3.3V, 50%
- Square wave: 1 to 100kHz, 0 to 3.3V, 50%
- Pulse wave: 1 to 100kHz, 3.3V, 0 to 100%
- Triangle wave: 1 to 100kHz, 0 to 3.3V, 50%
- Ramp: 1 to 100kHz, 0 to 3.3V, 0 to 100%
- DC out: 0 to 3.3V
Electronic components tester
This tester is able to automatically identify and measure various components like:
Transistors including NPN, PNP, N-channel, P-channel mosfets, junction mosfets, diodes, dual diodes, resistors, capacitors (including EST) and another passive one.
There is automatic detection of the pin Connection.
Extra tools
Can analyze NECinfered code protocol (IR LED), Volt meter 0 to 40V DC, DS18B20 and DHT11 sensors etc.
- Resistor: 0.01 Ohm to 50MOhm
- Inductor: 10uH to 1000mH
- Triodes: gain, type, Use etc.
- Misfit: Cg, Vgs, Uf, Vt, diode
- Triac: Gate voltage
- Capacitor: 25pF to 100mF, ESR, Vloss
- Battery: 0.1 to 4.5V
- V-meter: 0 to 40V DC
- DS18B20: 0 to 85 ℃
- DHT11: 0 to 60 ℃, 5 - 95%
- IR LED: NEC protocol
NOTE
- 1. TRIODES: Ices, ICEo, Uf are displayed only when valid
- 2. DIODES: Junction capacitance and reverse leak current are displayed only when valid
- 3. MOSFET: The turn-on and turn-off voltage of the FET must be less than 5V
- 4. MOSFET: Displayed only when there is a protection diode
- 5. CAPACITOR: Vloss is displayed only when valide
- 6. INDUCTOR: Two-legs components and measure inductance when the resistence is less than 2.1kOhm
Connectors
- IN: signal IN 0 to 40V
- DDS: output of signal generator
- DSO: input of oscilloscope
- Test socket: connect part to any pin of 1, 2, 3. K-A-A area is special for Voltage testing, see manual (included in package)
Included in package
DSO-TC3 meter
High voltage probe P6100
Ordinary probe
Test hooks
Adapter
Charging cable type-C
5V charger EU type
Paper manual
SPECIAL OFFER: Durable case for free
You may also like
